Flowers and bows made from ribbons for a headband. A beautiful DIY headband with a bow. Bows for gift boxes

This headband is very simple to make, but it looks amazing on your hair. The product is addressed to coquette girls who are constantly looking for new jewelry options. Bows are perhaps the most girlish and delicate accessory. It always looks beautiful on hair, be it a ponytail, braid or braid. And the headband is a universal decoration that even girls with short haircuts. And the hairstyle will always look fresh and fashionable. No need to grow it long hair to try on bows, and this headband with flirty decor is a direct confirmation of this.

For the current accessory we will need:

4 pieces of white ribbon with blue polka dots – 2.5 8 cm; 4 pieces of dark blue ribbon with white polka dots – 2.5 7 cm;
2 pieces of white ribbon with blue polka dots – 2.5 7 cm; 2 pieces of blue tape – 0.5 25 cm;
1 piece of white tape – 1.2*10 cm;
silver hugger with sharp rays;
half bead-crystal aquamarine color – 1.6 cm;
a thin metal rim, covered with or without white tape.

The color scheme proposed for making the bow looks very beautiful. This decoration will suit a white, blue, light blue, black outfit. But, naturally, this option is far from the only one. For a little girl, pink or other rainbow and variegated colors are more suitable. And this unique bow is more like an accessory for a schoolgirl. Why not wear a headband with a small bow in the morning before school. The decoration will not cause outrage among teachers, as it looks discreet and stylish.

The work presented is perfect occasion practice handling the tape. You don’t have to create any intricate petals or combine small satin blanks into ornate elements. Everything is extremely simple and clear. You will work with strips of satin, which should be singed, folded and formed into voluminous folds, and then glued into a single product. Get ready for the fact that any kanzashi product cannot be made without sharp scissors, a lighter and a glue gun.

Headband using kanzashi technique step by step

1. Select fittings for the job. Refer to the list given here, or choose your own, no less wonderful, color combination. Perhaps, looking into the craft goods department, another thought will come to you and you will decide to experiment.

2. The bow will consist of three layers: the first - of four white loops with blue polka dots, the second - of four blue loops with white polka dots, the third - and two white loops with blue polka dots. All loops are performed in the same way, using the same technique, which is demonstrated in the photo. Fold the strips in half, with the right side of the tape facing up.

3. Make 4 identical loops from a tape measuring 2.5 * 8 cm. In addition to the fact that the ends of each strip should be closed, they also need to be gathered on both sides.

4. Make all 10 loop stripes for beautiful decoration.

6. Assemble a lush multi-layer bow by gluing individual tiers.

7. This master class shows another type of simple loops, which are often used when modeling American bows. But this element is optional. Take thin blue stripes and in each of them, close both ends in the center so as to get two fastened rings.

8. Glue the two parts together.

9. Glue the resulting rings to the bottom of the bow.

10. Add a few more pieces of accessories: a headband, a thin white ribbon for wrapping the middle and a hugger with a half bead.

11. Wrap a white ribbon around the center of the bow and glue on a pretty aquamarine center. All parts are glued together with hot glue.

12. Finally, glue the bow to the hoop.

Despite its simplicity, the hair decoration looks very beautiful and elegant. Anyone can make the same product; its cost will be a pittance. If creativity inspires you, then you can make the same bows in the shortest possible time for all occasions.

You might also be interested in:

Kanzashi for beginners, step by step photo lesson,…

Whether it is strict or frivolous, elegant or voluminous - bows can create a special festive mood. The luckclub portal invites you to make various bows for all occasions with your own hands, and our simple master classes and the instructions will help you with this.

To sew a voluminous bow, you don’t need many tools, and you don’t have to have one at all. sewing machine, just a simple understanding and the ability to sew by hand is enough.

For work, prepare:

textile;
needle and thread in the color of the fabric;
pencil;
ruler;
scissors.

This master class uses checkered fabric, but you can choose the color and print of your choice.
Cut out 2 rectangles from fabric measuring 12.5x25.5 cm and 6x6.5 cm.

Lay out a rectangle bigger size Right side up, fold in half widthwise and sew. We turn the resulting part inside out.

Fold the pieces in half lengthwise so that the seam is in the middle, sew the ends together and turn them inside out.

We take a small rectangular piece of fabric and do all the same manipulations as with a large rectangle.

We assemble the larger rectangle with an accordion and thread it through the smaller one.

We straighten it and our bow is ready.

Volumetric bow made of corrugated paper, step by step with photo

Working with corrugated paper is a pleasure. With its help you can easily decorate an apartment or even a whole room in honor of special holiday. There are several techniques for creating bows from corrugated paper, but we propose to master one of the simplest ones, where the only materials and tools are scissors, the paper itself and glue.

Step 1. Cut out a rectangle from paper with a length equal to the width of the corrugated sheet and a width of 20 cm.

Step 2. Find the middle of the rectangle in width and bend the edges of the paper to it.

Step 3. From the same rectangle, cut a piece of paper with a length equal to its width and a width of 1.5-2 cm.

Step 4. Conventionally, we find the middle of a large rectangle and bend its ends to it.

Step 5. We assemble the blank for the bow with an accordion and go around the center with a previously cut piece of paper. On the back side of the bow we glue the ends of the segment.

A voluminous bow is ready to decorate a room or become part of the decor of any craft.

Volumetric bow on the headband, master class

In this master class we will tell you how to design a headband and make a beautiful and voluminous bow for it.

Tools and materials used for work:

headband;
fabric at your discretion;
thread with needle;
glue “Moment” Crystal;
glue gun;
scissors.

We cut out 2 blanks from fabric. We will make a bow from one piece measuring 16x23 cm, and from a second piece measuring 3x40 cm we will make a cover for the headband.
Important: the length of the headband is 37 cm and the width is 1 cm.

1. Mark a strip of fabric, dividing it into 3 equal parts.

2. Apply “Moment” Crystal glue to the upper edge of the fabric and bend the edges of the fabric to the first mark along the entire length.

3. Bend bottom part fabric about 1 cm inward and stitch along the entire length with stitches.

4. Apply glue to the top of the workpiece and glue the ends. After the glue has dried, pull out the thread.

5. Put the cover on the hoop.

6. Cut off the excess and glue the ends into the middle.

7. Make a bow. Take a rectangular blank for the bow and glue its long edges.

8. Find the center of the workpiece and glue the edges to it.

9. Fold the rectangle along its width like an accordion, forming a bow, and glue the folds together with a hot gun on both sides.

10. Using a hot gun, glue the bow to the headband.

11. Cut a strip from the same fabric and glue it to the center of the bow.

Volumetric bows on dresses, photo

Volumetric bows on chairs, photo

How to assemble a voluminous, tightening bow, detailed instructions with photos

It's hard to imagine a wrapped gift without a chic bow as decoration. Can serve as a material for a bow satin ribbon, brocade ribbon or ribbon used to decorate boxes.

To begin, cut a 2 meter long ribbon from a skein. The width of the tape depends on the desired volume. The wider the ribbon, the more magnificent the bow will be. This instruction uses 2.5 cm wide tape. Next, wrap the tape around your hand.

Remove from hand and cut off corners on each side.

We connect the cut corners.

We tie a narrow ribbon of the same color in the middle of the bow.

We take each layer of ribbon out one by one from the middle of the bow and turn it inside out. reverse side.

The lush bow is assembled.

Beautiful voluminous bows for girls, photo

Volumetric kanzashi bows, master class

Jewelry made using the kanzashi technique always looks expensive and original. We invite you to make an unusual bow with us, which can later be glued to a hairpin, to a brooch blank or to an elastic band.

From satin ribbon 2.5 cm wide in two compatible colors, cut out 4 pieces 20 cm long.
We fold 2 pieces with the wrong sides facing each other (ours are red and white).
We singe the corners of the ribbons so that the ribbons stick together.
Turning the tape inside out, fold it in half so that the top edge does not reach the bottom 2 cm.
Turn the tape over to the reverse side and fold its top towards the center of the connection of the ends.
We extend the long edge, connecting it to the short one.
We fasten the part with a tailor's pin. We make 2 such blanks.
We take two pieces of tape again and do the same steps as with the previous ones, only this time the bottom edge should be 2 cm longer than the top. Thus, we will get a mirror image of the first blanks.
We sew stitches on each of the blanks and pull out the pins.
We sew identical pieces together in pairs, tightening the centers.
Glue the central parts of the bow to the outer ones.
Glue the parts of the bow onto a piece of felt or foamiran measuring 2.5x1 cm.
Use a 1 cm wide satin ribbon to cover the joints of the bow parts and decorate with rhinestones.

Volumetric bow for a girl, step by step with photos

For creating voluminous bow for a girl, prepare:

satin ribbon 2.5 cm wide;
glue gun;
scissors;
felt;
beads.

1. Cut a satin ribbon 2.5 cm wide into 10 cm long pieces. To create this bow, a ribbon of three colors is used: white, yellow and milky. Each color will require 11 pieces. If you want a single-color bow, cut 33 pieces 10 cm long of the same color.

2. Make a petal. Take a piece, fold it face inward, pressing well in the center.

3. Drop a drop of glue into the center, gluing the middle.

4. Holding the petal blank in the center, bend the edges, forming the letter M in the middle.

5. Apply a drop of glue to the tip of the tape and, with the front side inward, glue first one end of the tape, then the other.

6. Glue the ends together. We make 33 such petals.

7. Glue the petals one by one onto a piece 4.5 cm in diameter.

8. Decorate the joints of the petals with rhinestones. You can glue an elastic band or a hairpin to the bow.

Video: voluminous ribbon bow

Large voluminous bow for discharge from the maternity hospital, step-by-step instructions with photos

Preparing for a significant event such as discharge from the maternity hospital, each future mom wants everything to look beautiful and perfect, including the bow.

You can make such a bow yourself by preparing the following materials:

9 pieces of satin ribbon measuring 5x20cm;
7 pieces of organza ribbon with lurex measuring 2.5x18 cm;
7 pieces of satin ribbon 2.5x15 cm;
6 pieces of organza ribbon with lurex measuring 2.5x12 cm;
8 pieces of printed satin ribbon measuring 1x8 cm;
glue gun;
needle and thread to match;
felt base with a diameter of 6 cm;

We carry out exactly the same manipulations with all segments.

Glue the felt base to the center of the largest part of the future bow.

Next, layer by layer we assemble the future bow. Glue organza on top of part of the bow made from the widest ribbon, on top of the organza again part of the bow made from satin ribbon, only smaller in size, then organza again, and finally a layer with prints.

The bow is ready for discharge.

How to make a voluminous bow from fabric, master class

To sew a voluminous bow made of fabric, prepare:

3 rectangles from cotton fabric 10x50 cm;
1 rectangle of cotton fabric 50x30 cm;
square of cotton fabric 10x10 cm;
3 rectangles of velor 10x50 cm;
a rectangle of cotton fabric of a different color, 30x50 cm;
padding polyester 150 g, dimensions 10x10 cm.

We sew narrow rectangles of cotton along short sections.

Sew velor strips along the short edge.

We fold the cotton and velor face to face and stitch along all the edges, leaving a hole on one of them for turning inside out. Next, we turn the part inside out, straighten it, manually sew up the hole and iron it. In order for the bow to end up with ears, the short edges should be ground off diagonally.

We sew wide strips of fabric on all sides, also leave an opening for turning, turn it inside out, sew it up, and iron it.

Place the smallest rectangles face to face. Let's do the same steps as with the previous rectangles, leaving one side unsewn.

We fold a wide strip of cotton in the middle, stitch it, and iron the seam.

We thread the bow into a ring made from padding polyester blank.

We pin the tails to the back side, and in order to prevent the bow from falling apart, we manually sew a padding polyester ring to the bow itself. The bow is ready.

All little fashionistas love various headbands and bows. Today I suggest you combine two tasks and make a very beautiful and stylish headband with a bow.

It’s not at all difficult to make; even a novice needlewoman can do it.

To make an openwork bow you will need:
satin ribbon 5 cm wide (approximately 30 cm)
satin ribbon 1 cm wide
beads
needle and thread matching the color of the ribbons.

Let's start making:

Fold the wide ribbon in half so that the cuts are in the middle. Sew at the junction and slightly gather, thus forming a bow.

Now let’s start decorating our bow with flounces made from a narrow ribbon.

We make two stitches on the needle, and with the third we sew the shuttlecock to the bow. We only attach the top part of the bow.

This is the kind of shuttlecock fold I get.

The sewn fold needs to be secured again so that it does not “walk” along the thread.

Sew the rows.

Let's turn.

We hide the ends.

You can sew on the beads right away, or you can sew them on a ready-made bow. At your discretion, the beads can be sewn on or glued with a hot gun.

We attach the bow to the headband with a ribbon.

That's all, the original headband with an openwork bow is ready.

I can imagine how happy your little fashionista will be if she received such beauty as a gift.

Get inspired by an idea and create.

New Year and others winter holidays is just around the corner, but you can still have time to buy something on a Chinese website to make your home feel festive and cozy. We have made for you a top selection of popular jewelry and other products that you just can’t do without these holidays. Let's see what interesting products you can order on the Aliexpress website this year.

Braided hair with with a beautiful bow always look smart, but they can come undone during children's party. The headband perfectly holds children's hair, maintaining their hairstyle. That's why the best option for young beauties there will be a headband with an elegant bow attached to it.

To make the headband you will need the following materials:
- wide orange rim.
- glue gun.
- scissors.
- satin yellow ribbon.
- golden crepe ribbon, no more than 0.5 cm wide.
- lighter.

Sequence of creating a rim. Tape yellow color Cut at least 5 cm wide into elongated pieces. In total, 18 pieces should be prepared, the size of which is 7x5 cm.

Now from each part we create petals for the rim. We divide the long side of the rectangle in half and fold it in half along this line, combining both cuts together.

Holding the piece with the finger of your left hand, carefully make several small folds along the raw cuts. We fix the completed folds in this position by scorching the edges with fire, while simultaneously soldering the layers of tape and burning the cut.

We get such a lush petal, now we create the same details from the remaining rectangles.

Now you will need a grosgrain ribbon with golden threads. We cut it into small pieces, 4 cm long each. We prepare 16 of them in total.

As a result, we get a small loop. Now we glue it on top of the prepared yellow petal.

Repeat this action with the remaining petals. But at the end of the work, two parts made from yellow ribbon will remain without adding a golden loop. Now we proceed to connecting the two halves of the bow. To do this, prepare two parts from tape yellow tint, whose sides are 6.5x5 cm.

Then we glue the second row of yellow parts, securing them like the previous ones.

In the third row we attach only two petals, so that only their upper corners overlap.

Now we take the petal without adding a golden ribbon and attach it to the remaining space of the base part.

The first half of the bow is ready, let's start creating the second, the same, following the entire sequence.

Next, take a wide hairband, step back 5 cm from one edge and carefully attach the first half of the bow. We place its wide side towards the edge of the rim. Then we attach the second half of the bow, matching their narrow sides.