A broken zipper on clothing is an unpleasant moment that requires immediate attention in order to maintain the aesthetics and functionality of the outfit.

How to replace a zipper on clothes?

How to replace a zipper on trousers, is it difficult to do it yourself? Professionals say that this task is completely solvable for those who know how to handle a needle and thread.

Causes of zipper failure

There can be several reasons for a zipper failure:

• low quality fittings
• dishonest work of a clothing manufacturer
• improper operation

Among the most common types of defects are a broken “dog”, flying teeth, and unraveling seams.

In any case, in order to replace the zipper, you will need basic sewing supplies: scissors, thread, needle. If you have a sewing machine at home, this greatly simplifies the process and allows you to achieve a better result.

How to replace a zipper

Each shop that replaces zippers on jackets, trousers and jeans is guided by the same algorithm for repairing parts. So, in order to understand how to replace a zipper on trousers, it is necessary, first of all, to remove the broken fittings from the clothing. The threads attaching the zipper to the trousers must be carefully cut. Maximum care should be taken to avoid damaging the product. The new zipper should be the same type as the old one (or matched to the clothing). For light summer trousers, fittings with thin plastic teeth are suitable, while for an outfit made of thick fabric, it is better to choose a zipper with metal teeth.

How to sew a zipper

Sewing on a zipper is the most crucial moment: the part is applied to the edge of the fly and secured with strong and frequent stitches (the upper tail should be bent down). The stitch is laid along the entire length, after which you can begin sewing on the second part of the lock. It should be taken into account that in order to maintain the aesthetics of the product, the stitches should pass only through the inner fabric, without going outside.

For those wondering how to replace a zipper on jeans, the steps above will also work: Jeans have the same construction as trousers.

Entrust the task to real professionals

If the situation with trousers and jeans is not too difficult: the zipper on them is covered by the fly, then the question of how to replace the zipper on a jacket or coat requires special attention. Those who do not have the talent of a tailor should not despair: real professionals can easily cope with this task. A modern home of household services and clothing repair are ready to come to the rescue and extend the life of your favorite things.

Having experience in clothing repair, many processing secrets were revealed to me, including zipper replacement in jeans. It turned out that for me it took 20 minutes.

There are old, but loved jeans. as you can see the zipper is broken.

Before removing the zipper, use chalk to mark its border and the location of the last connecting link.

Now pull out the zipper, remove the finishing stitch and the part from the stitching to the crotch. Jeans have this “disassembled” look to accommodate a new zipper.

Take a suitable length or. Place it “face down” towards the inside of the codpiece, towards the previously marked line. Align the bottom chalk mark with the last link. “Give” two lines of lightning.

Pin the flying part of the codpiece. The “tail” is important, bend it over and pin it with a pin so that it doesn’t get caught under the stitching.

Sew the codpiece in two lines, trying to get into the old punctures. Remove all pins. Gender of the matter replacing a zipper produced.

Open the zipper and stick in the connecting part, placing the pins across. Close the zipper and check if there are any unnecessary irregularities.

From the wrong side, pin the piece aligning with the edge of the zipper. Sew the zipper on the front side.

Close the zipper and line up the seam under the codpiece and secure with pins.

From the crotch seam to the codpiece, sew two lines along the old punctures. Restore the stitching on the waistband.

We sew the zipper into the jeans only after the pockets are completely made on the front halves.

We strengthen the codpiece and slope, “How to sew jeans” with glue. We glue the codpiece completely, the slope - half the width.

We sew in the lower short edge of the slope, cut off the allowances with a step, and cut out a corner.

Turn it inside out and set it aside. The slope overlaps the codpiece in length; in width it is 1.5 cm smaller than the codpiece (seam allowance).

We process the codpiece with bias tape, placing it on the rounded area.

Notching the seam allowance only bindings on a rounded area. We also use the trim to process the open cut of the slope.

We bend the trim around the cut, fold it in half, iron it, and attach it. IN finished form, when applied, the slope turns out to be longer and slightly narrower than the codpiece.

We lay out all the parts - codpiece, slope, front halves. We sew the middle seam on one front half, to which the slope will be sewn.

Sew on the codpiece.

Fold the seam allowances onto the codpiece, sew the codpiece close to the seam, cut off the seam allowances close to the stitching.

We attach the zipper to the codpiece, as shown in the photo. The zipper stopper is located below the future line, which we will use to sew the codpiece along the front side. The foot should fit between the stopper and the future stitching sewing machine. Place a chalk mark where the stitching will be located. The zipper tape should not be located below the codpiece.

Using the chalk mark we specify the stitching lines for the codpiece. Iron the seam allowance below the codpiece.

Attach the zipper braid to the codpiece.

Let's try on the slope.

We pin the unsewn zipper tape to it.

Place the second front half so that the edge of the codpiece coincides with the seam lines.

Fold in the added 1.5 cm allowance and attach the zipper and the other half to the slope.

At the end of the seam we make a bartack.

Then, we place the pressed seam allowance of the right front half onto the seam line of the left half, pinning it perpendicular to the seam.

And attach it with a finishing stitch.

We bend part of the slope on the wrong side and fasten it on the front side with a zigzag seam.

Important! Do not trim the top section of the zipper until you sew on the waistband.

The article was prepared based on materials from the forum topic

Modern wardrobe items are equipped with many amenities for more comfortable wear. This includes lightning. Thanks to its presence, the trousers can be easily and securely fixed at the waist.

We are used to this fastener, which even a baby can easily handle. But sometimes the easy movement of the zipper is disrupted, and the fastener becomes unusable. For example, if you encounter breakage of the teeth, this will lead to the impossibility of connecting its parts.

You will have to start replacing the fittings. You can sew it into women's and men's trousers yourself, using a little cutting and sewing skills. You won't have to spend a lot of time. The acquired skill will also be useful when sewing new clothes with such a fastener.

Sewing a fastener into trousers is not as difficult as it seems at first glance. You can deal with it yourself, without turning to professionals in the studio. This does not require any special skills or abilities.
The main thing is to choose the right consumables and the right tools.

How to choose a zipper for trousers

The selection of accessories must be approached with special care.

• Average length, suitable for a given item of clothing, is about 9 cm.
• For products high waist use size about 8–9 cm.

You can purchase any of them in specialized stores.

What you need for work

• safety pins;
• scissors;
• chalk or pin pencil;
• ruler;
• iron;
• sewing machine.

When the required tools and materials are prepared, you can begin to work.

Let's figure out how to replace a zipper or add one to pants sewn without a zipper.

• If you are working with a product that did not have a zipper, you will have to perform this preliminary step. Replacing a damaged fastener with a new one will do without this step. Start carefully rip out the front center seam on the trousers from the wrong side in the place where the runner itself will be sewn.
• Then spread the trousers on a hard and flat surface. A wide table, not crowded with foreign objects, is suitable for this.
• Place the zipper on the surface of the trousers and use a pencil pin We note the measurements of its location.
• Since the zipper will be positioned without a codpiece, on the right side you can step back about 2 cm from the measurement and carefully trim off the excess fabric.
• Again place the zipper with the front side on the inside of the trousers.
• For greater convenience when sewing, you can Carefully pin the material to the product using safety pins.
• We fix the interval 3 on the sewing machine and sew one side.
• After this you can fasten and unfasten several times zipper, making sure that nothing interferes with the slider.
• Fasten the other half back and fold the trousers. If the position is even, you can start sewing the second part.

Important: when processing the second part and carefully decorating the bottom of the fastener, experts recommend turning the sewing machine wheel yourself.

This is done so that the needle does not jump into the area of ​​the fastening teeth.

The product is almost ready. To finish the job it remains again sew trousers in the groin area.

We remove the remaining threads and skip the seam on the sewing machine.
We check whether the fastening is processed correctly, fasten the lock several times to make sure that the slider moves comfortably.

After finishing the work, the seams It is recommended to iron several times for precise fastening and secure fixation.

Thus, with a few simple steps, you can carefully sew a zipper to your trousers.

Reference: If you buy a longer lock, you can shorten it yourself.

To do this, you will need to measure the required length and carefully cut off the extra centimeters on top. When sewing, bend the protruding teeth.

Lightning with codpiece

Trousers and jeans with a codpiece always look more neat and discreet. Most modern products are produced with this part.

Basic information about the codpiece

The finishing part, which is called a codpiece, is a kind of valve or strip that covers the zipper area.

IN male version it is located from left to right. In women's it's the other way around.

If you don’t have one or if you sew your own trousers, you can make such an overlay yourself. The process is not very complicated and takes a minimum amount of time.

Codpiece pattern and technological process

To get started, you need to prepare consumables and all tools.

Required accessories:

• safety pins;
• scissors;
• ruler;
• chalk or pin pencil;
• iron;
• sewing machine.

To pattern the overlay, you can use the fabric left over when sewing the zipper to the trousers.

Operating procedure

• First you need to decide on the size of the part itself and its location.
• We carefully rip out the front seam of the product from the wrong side.
• Use chalk or a pencil to mark the location of the slider.
• We retreat 1.5–2 cm along the edges and carefully cut them off, rounding them towards the end of the arrangement.
• Now you can sew the zipper itself, and only then measure the necessary parameters for the lining.

Reference: The zipper can be attached to the pants with safety pins for precise fixation when sewing.

• Carefully sew the seam. After this, it is recommended to check the slider several times for comfortable and free movement along the mounting surface.
• Now let's measure the pad itself. Usually it is no more than 3 cm. On the wrong side, mark the top mark with chalk or a pencil pin. Next, using a ruler, mark the codpiece itself along the zipper. We draw a parallel line, rounding it towards the end of the zipper.

Important: when sewing a zipper on women's product the codpiece is located on right side products. On men's trousers - on the left side.

• After preparing the necessary contours, the not yet realized the codpiece can be bent and ironed. This will help make a better and more even seam.
• Then we start the first seam on the far side. It's better for this use an overlock stitch: stitch 4 wide, and leave the stitching interval at half a centimeter.
• After processing the far seam, you can make the near one.
• Carefully bend about half a centimeter and stitch it in the same way.
• After preparing the codpiece, you can sew on the fastening itself. We retreat about half a centimeter and attach the zipper to the trouser leg with safety pins.
• The sewing machine needs to be set to a regular straight stitch. The 3rd interval is suitable for this. Then we perform a regular stitch. Now the fastening itself with the codpiece is ready.
• Next you need Carefully sew both parts of the trousers, stitching the trouser legs in the groin area and rounding the location of the zipper.

Advice: if the old fastener breaks, you can replace it using the old samples. This work is done 2 times faster.

Conclusion

The zipper on the trousers helps in a more secure fit on the wearer's body. If the zipper is missing or broken, you can sew it in yourself. You can also make your own codpiece that hides the slider from prying eyes. This process does not require serious cutting and sewing skills; it is carried out step by step and takes a minimum amount of time.

All more women today, inspired by the idea of ​​having their own unique wardrobe, they strive to independently comprehend the art of cutting and sewing. But at the stage of seemingly details, amateur seamstresses encounter difficulties. For example, not everyone knows how to sew a zipper into trousers or properly handle a codpiece. Meanwhile, without this skill in sewing not enough. The main thing here is not to give up and boldly start practicing.

Basic Tools

It’s better to start with clothes with open sides - these can be sweaters, vests and jackets. And then you can start working on trousers with skirts; this is also not as difficult as it seems at first glance. Step-by-step instruction This will demonstrate how to sew a zipper into trousers.

Tools:

• zipper with lock;
• two front parts of trousers;
• invisible pins;
• a piece of chalk or soap;
• sewing machine (with zigzag foot and overlocking device).

Where to begin

1. You need to take the right and left pieces of the trousers and fold them facing each other in the middle of the front. This will be our area of ​​work. Using invisible sewing pins, you need to pin together the place where the zipper will be placed.
2. Next, you need to pin a section of the middle seam, which starts at the front of the pants and ends at their inseam.
3. The next step is to sew it with a small stitch using sewing machine(don't forget to remove the pins as you go). There is no need to process the allowance.
4. After laying out the product on the table, we will get two identical facings (on the right and left sides). Next, using a ruler and chalk, mark the left edge (4 cm) and the right edge (2 cm).
5. Using a regular or overlock foot, we will process the marked sections of the facings, rounding the left one to the mark of the future cut for the snake. Thus, we got a wider left facing - 4 cm, and a narrow right facing - 2 cm.

How to properly sew a zipper into pants

1. Let's start by marking the location for the zipper. To do this, mark a line 5 mm wide on the right fragment of the cut and sweep the facing along it from the inside.
2. Next, you need to pin the snake to this area, bringing the teeth tightly to the fabric. To completely close the zipper, make sure that the pawl of the closed zipper at the top does not reach the top edge of the trouser waistband by 3 mm.
3. If you turn the product inside out, you will see the zipper braid that lies on the left facing. In this position it needs to be pinned, but only to the facing.
4. Stepping back from the fold of the material by 2 mm, sew the fastener suitable foot. Sticking threads need to be tied in knots from the inside out and cut off.
5. Next, you should process the snake braid with two lines - along the edge and next to the teeth.

Marking zipper stitching lines

Now is the time to adjust the size of the zipper if it is too long. Simply cut it to the required length and stitch the end onto the slope. As for the width of the stitching, it can vary depending on the size of the product from two and a half to three centimeters.

Turn the work over to the front side. Now we chop off all the layers of material, not forgetting to grab the bottom facing with the snake ribbon already attached. Next, you should mark and draw a line at a distance of 2.5 cm from the center.

You only need to line up a straight spot along the line, before turning. The second stitching is done 5 mm from it.

Such meticulous markings will make it easy to line up the decorative line of the snake with the end of the seam right before the transverse marking. The second line is made to the width of the foot. The threads should be pulled inside out and secured with knots.

What is a codpiece

It's time to learn how to sew a zipper into trousers with a codpiece. This detail, also called a fly, will help make the zipper beautiful.

A codpiece is a slit or flap with stitched loops that fastens at the front of a skirt, trousers or shorts. Designed for processing trouser fasteners with buttons and loops.

The location of the codpiece depends on the model of trousers being created. So, before sewing a zipper into women's trousers, on the right side of the trouser leg we fold the fly allowance inside out and iron the fold. You don't need to do this on the other leg. If we sew men's trousers, we do the same thing, but with the left fragment of the trousers.

There are two ways to sew a zipper into trousers: it can be inserted with a solid cut piece of fabric covering the fastener, or with a stitched one. Let's take a closer look at the method using a one-piece valance. Its peculiarity is that the zipper is completely covered from the inside with a special element.

Design of a one-piece codpiece

1. Place a slope under the open zipper of the right leg and pin a strip of the fly. Then turn the product inside out towards you.
2. Next, you should sew this seam using a sewing machine. In this case, you need to try to get as close to the facing line as possible. Afterwards, be sure to check whether the zipper is unfastened and fastened to make sure that there is no fabric on the lock and nothing is blocking its movement.

Sometimes when wearing trousers (when they fit tightly), the hem may come off. To prevent this, it is better to do the fastening at the intersection of the finishing stitch along the fly.

1. The next step is to design the middle seam. To do this, you need to put the trouser legs into each other, pin together the area that has not yet been sewn, stitch and process the allowances (with an overlock or “zigzag” along the entire length, plus the front area that has not been previously processed).
2. Pin the entire middle seam allowance to the left side.
3. Now you need to attach bottom part fly and extend the double stitching (which serves a decorative function) until the marking line is beveled.
4. The last step is to stitch the middle seam of the pants using double stitching. At the beginning of the fastening cut and where the interrupted parts of the decorative seam are connected, we will place even zigzag fastenings.

Thus, we learned how to sew a zipper into trousers. It remains to stitch the middle seam of the trousers using double stitching.

Conclusion

If a woman wants to look original and unique, then nothing can stop her from doing so. A detailed information about how to sew a zipper into trousers, cutting, sewing and much more, will finally dispel all fears and doubts. Try it too!